Hunter 27189 Manuel d'utilisation et d'entretien télécharger pdf (Page 1)

Original

Remote Fan & Light Control

Model 27189

Ratings: 120 VAC, 60 Hz, 2.0 Amp Fan Receiver Weight 16 oz.

300 Watt incandescent light

Read and Save these Instructions

Caution: Risk of Electrical Shock!

All wiring must be performed in accordance with national and

local electrical codes. If you are unfamiliar with the wiring

codes, you should use a qualified electrician.

To avoid overheating and possible damage to other equip-

ment, do not install to control a receptacle, fluorescent light

fixture, motor operated appliance, or transformer-supplied

appliance. Use only to control one paddle-blade ceiling fan

and incandescent light fixture.

Notes:

1. This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

2. This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to radio com-

munications. However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

3. For use only with electrically reversible ceiling fans rated at 2.0 amps or

less, and fan incandescent light kits rated at 300 watts or less.

4. Not for use with shaded-pole or non-reversible motors.

5. Medium and Low fan speeds are determined by the Original

control

and thus may vary from the factory settings due to normal motor variations.

Before Installing the Original

Control:

1. Confirm that your Hunter Original

ceiling fan is electrically reversible.

Look for a reversing switch on the switch housing below the motor. Refer

to Figure 1.

2. Use the pull-chain switch to set the fan speed to the HIGH position

before installation. Do not use the pull-chain to change the fan speed

after installation, as damage to your ceiling fan or control may result. The

speed of the fan should only be changed by the Original

control.

3. Set the ceiling fan light kit to the ON position before installation. The

light level should only be changed by the Original

control.

Receiver Installation:

1. Disconnect power to the ceiling fan and light kit at the main electric

panel. Remove fuse or move circuit breaker to the OFF position.

2. IMPORTANT! Before installing this control, change the factory default

dip switch settings to your own unique code. Refer to Figure 2. Be sure the

dip switch positions of the transmitter and receiver match, or the ceiling

fan will not function.

Select different combinations of dip switches to prevent mis-operation due

to other remote control fans, garage door openers, etc.

3. This Original

remote control mounts between the ceiling and fan

hanger bracket. Therefore, if the fan is already installed, it will need to be

taken down.

4. Wire the power leads coming from the ceiling outlet box. Connect the

main wires from the

top

of the control – white to white, and black to

black. See Figure 3. Push the wires up into the outlet box and arrange the

wire connectors to point upward. Separate the wires so that the black

wires are on one side of the box and the white wires are on the other.

5. Bring the control up to the ceiling. Feed the bare copper ground wire

down through the center hole of the control. Use the lag screws (includ-

ed) to hold the control and and the fan mounting bracket in place. See

Figure 4.

6. Mount the fan to the fan hanger. Connect the white wire from the con-

trol to the fan white wire and the black wire to the black. Connect the

bare copper wire to the green ground wire from the fan. Connect the red

wire from the control to the fan through-wire that goes directly to the

light kit. See Figure 5. Push the connections up through the center hole

into the ceiling outlet box.

7. Complete the installation of the fan by following the instructions sup-

plied with the fan.

8. Restore power at main electrical panel.

Wall Control Installation:

1. Remove rocker style wallplate (not included) to expose the wall wiring.

Disconnect the existing switch and remove from the electrical box.

2. If 4 wires are visible, connect each black wire to an Original

control

black black wire. If 2 wires are visible, connect each to an Original

control lead. Use 2 of the large wire nuts supplied to make the connec-

tions. Refer to Figure 4.

3. If a ground wire is provided in your electrical box, attach it to the

ground screw near the bottom of the mounting plate.

4. Gently push wires and wall control into the electrical box. Attach the

Original

control to the switch box with the two screws provided.

5. Verify that the master switch is in the OFF Position. Press inward on

each side of the wall control to remove face cover. Set the dip switches to

match the dip switches in the receiver. Install a 12 volt battery (A23,

MN21, or equivalent). Replace the face cover.

Operation:

1. Slide the master switch to the ON position. After a 1.5 second delay, the

light will turn ON at maximum brightness.

2. Light Operation:

• Press and quickly release the light button on the wall mounted control

to turn the light OFF or ON. (Light will come ON at maximum brightness.)

• Press and hold the light button for more than 1 second to turn the light

ON and decrease from maximum brightness to OFF.

• Release the light button when the desired light level is reached.

• Continue to hold the light button to repeat the cycle. (Maximum–light

level decrease–OFF)

• While the light is ON, holding the light button will decrease the light

brightness.

• Turning the light OFF resets the dimming function. The next press of the

light button will start at maximum brightness.

3. Fan Operation:

• Press the High, Medium, or Low speed buttons to turn the ceiling fan

ON at the desired speed.

• Press the fan OFF key to turn the ceiling fan OFF.

For best fan operation: Allow the ceiling fan motor to start on High, then

select the desired speed.

4. Manual Light Switch Operation:

To turn the lights ON without battery power to the wall control turn OFF

the wall switch for 5 seconds, then turn the master switch back ON. The

light will turn ON at maximum brightness, and the fan will be OFF.

5. For everyday operation, leave the master switch ON. However, if the

control will not be used for an extended period of time (5 days or more),

turn the master switch OFF.

Symptom

1. No functions operate.

2. Operates only at close range.

3. Inconsistent operation.

Possible Causes

Main Power not restored.

Fan pull chain not set to High.

Light pull chain not set to ON.

Receiver wiring incorrect.

Transmitter and receiver dip switches do not match.

Battery too weak.

Cable or power lines in ceiling run over fan.

Battery too weak.

Signal partially blocked from reaching receiver.

RF interference.

Continuing RF interference.

Solution

Replace fuse. Turn ON circuit breaker. Turn ON wall

switch.

Turn OFF power at wall switch or main electric panel.

Set fan to High speed.

Set light kit to ON.

Verify wiring connections.

Set transmitter and receiver to same dip switch setting.

Replace with new, alkaline battery.

Re-orient any cables or wires.

Replace with new, alkaline battery.

Extend antenna into ceiling box, or move it for better

reception.

Turn OFF wall switch for 5 seconds, then turn back ON.

Change dip switch settings to a different code in both

Transmitter and Receiver.

HUNTER FAN COMPANY ORIGINAL

CONTROL LIMITED WARRANTY

The Hunter Fan Company makes the following limited warranty to the original purchaser of the Original

Control (“Control”): Your Control is warranted to be free from defects

in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or

workmanship we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING

BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL

OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR

SUCH CONTROL. This warranty excludes malfunctions or failures which were caused by repairs by persons not authorized by us, mishandling, improper installation, modifica-

tions, or damage to the Control while in your possession, or unreasonable use. This warranty does not apply to batteries or to deterioration or damage to the product caused by

the use of faulty batteries. To obtain a replacement, return your Control postage prepaid along with proof of purchase to Hunter Fan Company Service Department at 2500 Frisco

Avenue, Memphis, Tennessee 38114. IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. SOME STATES DO NOT

ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE

LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

ON DIP

Transmitter Back

Receiver

ON DIP

Dip Switch

12 VOLT

Dip Switch

Power

Red

Black

White

Common

Fan

White/

Neutra

Black/

Hot

Through-Lead

for Light Kit

Green

Bare Ground

Copper from

Outlet Box

Receiver

Fan OFF

Fan Low Speed

Fan Medium Speed

Fan High Speed

Master ON/OFF

Light Button

Troubleshooting

Figure 2

Figure 5

Figure 6

1999, Hunter Fan Company Form 41443 (12/99)

Figure 1

Confirm

Reverse

Switch

Select your own unique code, being sure settings match in the

transmitter and receiver.

Electric Cable

Black

White

Bare Copper

Ground Wire

Control

To p

Wooden Building

Structure

Control

Original

Fan

Bracket

Bare Copper

Wire

Use Long Lag

Screws Supplied

with Control

Figure 3

Figure 4

Mount Directly to Structure

Wiring Diagram

For more information on Hunter Fan products, visit our website: www.hunterfan.com

Original 1
Model 27189 1

Résumé du contenu

Page 1 - Model 27189

Original®Remote Fan & Light Control Model 27189Ratings: 120 VAC, 60 Hz, 2.0 Amp Fan Receiver Weight 16 oz.300 Watt incandescent lightRead and Sav

Commentaires sur ces manuels

Pas de commentaire

Hunter 27189 Manuel d'utilisation et d'entretien Page 1

Naviguer en ligne ou télécharger Manuel d'utilisation et d'entretien pour Lumières des projecteurs Hunter 27189. Hunter 27189 Use and Care Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels